![]() ![]() Enter the right password for the wireless network and you are done. You’ll see the SSIDs for the Wifi network. Now, on your phone, smartphone or other wifi networks, try to connect to WiFi. It’s set for your wireless network in order to configure Linksys E2500 setup. You would be able to attach to all of them appropriate for your computer. Save some parameters.įor you, this will build 2 separate WiFi networks. Shift the protection mode for all of them to WPA Personal or WPA2 Personal. You’ll see the security of two separate Wi-Fi networks again. Save some parameters.Ĭlick on the sub-tab for Wireless Protection. For all wifi networks, make sure to use subtly different SSIDs so that you can distinguish them. Modify the SSID name of the wireless network on all networks. There are 2 different cellular networks you will see. Your main machine will be able to reach the Internet connection through Linksys E2500 once you update your Internet connection settings.Ĭhanging wireless network configurations will now be the next step.Ĭlick on the Wireless tab on the Linksys E2500 setup page. Enter the name and password of the PPPoE user provided by your Internet service provider. You would have to change the PPPoE settings for the DSL Internet connection. You will need to clone the MAC address of the main machine for the Wired Internet. Open the configuration tab of the Linksys E2500 Setup and start manually changing the Internet connection settings. Resetting the router would update the configuration of the router to the default factory environment.įor 15 seconds, push and hold the reset button on the router. If this default password doesn’t work, the router will need to be reset. ![]() The default password for Linksys E2500 setup is server, leaving the username void. The configuration page is a page where you can change network settings and it is protected by a password. It will ask you for a password for the router. Open the Internet window and enter 192.168.1.1 into the address bar. The Linksys E2500 router’s default IP address is 192.168.1.1. You can manually build a Guest Network.Īttach the modem and the device to the router via an Ethernet cable, like most Linksys routers. To build guest network access which was required for E1000, E2000, E3000 routers, there is no need to run the Cisco program. Guest entry to Linksys E2500 setup can also be handled using the configuration tab. This router can be installed with or without your Cisco Connect app or installation CD. Note: If you have not enough information, it is obviously recommended that you should get help from a person who has all the knowledge about this topic.Linksys E2500 setup is as simple as the setup of other Linksys routers. It is therefore better to take an expert's assistance in this regard. What you need to keep in mind is that when you reset your modem, you will lose your connection online. If you hold down this small button for approximately 20 seconds, (you may have to use a toothpick), then your modem will get restored to the factory settings. This can be done easily by clicking on the reset button at the back or at the bottom of your router. Nothing of the methods worked for me and I still not get access to my Cisco !Īll you need to do is to reset your modem. You tried different router IPs but nothing worked? Did you try the following IPs? In the list below we listed all known router IPs for the manufacturer Cisco. Then you can try these username/password combinations below to get access to your Cisco Linksys-E2500 wireless router. Sometimes the username and password doesn't work that we mentioned in the top of this guide. ![]() In this list are the most popular default username and password combinations used by Cisco. Try different ID/password combinations that are widely used by Cisco that you'll find below. If above login credentials doesn't work with your Cisco Linksys-E2500 router then try this method Enter the username & password, hit "Enter" and now you should see the control panel of your router.The default username for your Cisco Linksys-E2500 is admin.You should see 2 text fields where you can enter a username and a password.Type 192.168.1.1 (the default IP to access the admin interface) in the address bar of your internet browser to access the router's web-based user interface.Chrome, Firefox, Opera or any other browser) To get to the router login page it's necessary that you are connected to the router. But if you do not have the manual for your router or you do not want to read the whole manual to find the default login information then you can use the quick guide below. You'll find such information in the Manual of your Cisco Linksys-E2500 router. To get access to your Cisco Linksys-E2500, you need the IP of your device, the username and password.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |